111 results with digital objects Show results with digital objects
A ship propeller at Columbia Steel Casting Company
Two unidentified workers guide a ship's propeller on a crane at Columbia Steel Casting Company. Another worker is visible operating the crane from a booth in the upper portion of the photograph.
Atkeson, Ray
Building a mold at Columbia Steel Casting Company
A molder using a trowel to fine tune a large ship hull casting before the cores are set at Columbia Steel Casting Company.
Atkeson, Ray
Checking a mold at Columbia Steel Casting Company
Employees at Columbia Steel Casting Company check a mold after the pattern has been pulled.
Atkeson, Ray
Chiseling steel-cast components at Columbia Steel Casting Company
An employee using a pneumatic chipping gun on a ship hull frame casting at Columbia Steel Casting Company.
Atkeson, Ray
Cleaning a mold at Columbia Steel Casting Company
A molder blows off parting compound (white powder) from a mold before the pattern is pulled from the sand at Columbia Steel Casting Company.
Atkeson, Ray
Cleaning a steel-cast component at Columbia Steel Casting Company
An employee using a swing frame grinder on a large casting at Columbia Steel Casting Company.
Atkeson, Ray
Cleaning a steel-cast component at Columbia Steel Casting Company
An employee using a chipping gun to excavate a casting defect to prepare for a weld repair at Columbia Steel Casting Company.
Atkeson, Ray
Cleaning and finish grinding a steel propeller at Columbia Steel Casting Company
Employees at Columbia Steel Casting Company cleaning a casting with pneumatic chipping guns while two welders fill in flaws in a propeller casting.
Atkeson, Ray
Cleaning room at Columbia Steel Casting Company
An employee using a swing frame grinder on a stern frame casting in the cleaning room at the Columbia Steel Casting Company foundry. Caption from bottom of negative reads, “Center section in cleaning room. Pouring weight 50,000 pounds.”
Atkeson, Ray
Cleaning skeg from castings at Columbia Steel Casting Company
An employee using an electric swing frame grinder to clean skeg off a ship frame casting at Columbia Steel Casting Company. The caption at the bottom of the image reads, “Skeg being cleaned.”
Atkeson, Ray
Cleaning skeg from castings at Columbia Steel Casting Company
An employee uses a prybar to remove the slag after an acetylene cutting torch has cut the riser steel-cast component at Columbia Steel Casting Company.
Atkeson, Ray
Cleaning skeg from castings at Columbia Steel Casting Company
Two employees work on cleaning a casting at Columbia Steel Casting Company. One employee uses a cutting torch to remove rigging, and another uses a bar to hand chip off sand.
Atkeson, Ray
Cleaning steel-cast components at Columbia Steel Casting Company
Employees operating swing grinders on a ship hull cast at Columbia Steel Casting Company.
Atkeson, Ray
Cleaning steel-cast components at Columbia Steel Casting Company
An employee using a swing grinder on a stern frame casting at Columbia Steel Casting company.
Atkeson, Ray
Cleaning steel-cast components at Columbia Steel Casting Company
Employees using swing grinders, chipping guns, and pneumatic chisels on steel-cast components at Columbia Steel Casting Company.
Atkeson, Ray
Cleaning steel-cast components at Columbia Steel Casting Company
Two employees work on stern frame of ship at Columbia Steel Casting Company. One employee uses a cutting torch to remove a riser and one uses a pneumatic chipping gun.
Atkeson, Ray
Cleaning steel-cast components at Columbia Steel Casting Company
Employees using pneumatic chipping guns to clean a stern frame casting at Columbia Steel Casting Company.
Atkeson, Ray
Cleaning steel-cast components at Columbia Steel Casting Company
Two employees cleaning steel-cast components with an electric swing grinder and a pneumatic chipping gun at Columbia Steel Casting company.
Atkeson, Ray
Constructing a casting flask at Columbia Steel Casting Company
Employees at Columbia Steel Casting Company working to close a mold by placing the cope (top half of the mold) onto the drag (bottom half) of the mold.
Atkeson, Ray
Constructing a casting flasks at Columbia Steel Casting Company
An employee on a crane seat uses a slinger to fill a larger mold box with sand at Columbia Steel Casting Company.
Atkeson, Ray
Crane ladle at Columbia Steel Casting Company
An employee steadies a crane ladle as it is filled with steel from an arc furnace at Columbia Steel Casting Company.
Atkeson, Ray
Crane ladle at Columbia Steel Casting Company
An employee rakes the slag off the top of the molten steel in a crane ladle at Columbia Steel Casting Company.
Atkeson, Ray
Crane ladle at Columbia Steel Casting Company
An employee pouring steel into a crane ladle at Columbia Steel Casting Company.
Atkeson, Ray
Employees at Columbia Steel Casting Company
Two employees using grinders and chisels on a bullion pot casting at Columbia Steel Casting Company.
Atkeson, Ray
Filling flasks at Columbia Steel Casting Company
Employees using an open cabbed overhead crane ladle to pour a mold at Columbia Steel Casting Company.
Atkeson, Ray
Filling molds at Columbia Steel Casting Company
Four employees using a lip pour ladle to pour a large mold at Columbia Steel Casting Company.
Atkeson, Ray
Finish work on a steel propeller at Columbia Steel Casting Company
An employee grinds flaws out of a steel propeller casting while two other men observe at Columbia Steel Casting Company.
Atkeson, Ray
Finish work on a stern frame casting at Columbia Steel Casting Company
Four employees use pneumatic chipping guns to clean a stern frame casting at Columbia Steel Casting Company.
Atkeson, Ray